Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 14 Next »

Shelly Plus 1 (2).png

Introduction

For dealers, installers, and technicians specializing in smart home automation, the integration of advanced control and monitoring solutions for garage doors is not just about adding convenience for the homeowner; it's also about elevating the security and efficiency of the smart home ecosystem. This guide is designed to facilitate the installation of a Shelly Plus 1, combined with a 12V DC power supply and a reed switch, to achieve refined control over garage doors. This configuration not only supports remote operation but also enables precise status monitoring via the Shelly app, introducing a superior layer of automation and intelligence to your installations.

Required Components

  • The Shelly Plus 1 (Plus 1 UL) smart relay

  • The Shelly IP6610755 enclosure – This enclosure is specifically designed for robust outdoor applications with IP66 protection.

  • A reed switch (not provided by Shelly)

  • A 12V DC power supply (not provided by Shelly)

Some components needed for this solution will need to be sourced elsewhere.

The reed switch would be a 2-wire solution that is rugged to stand up to the elements in a garage and around moving parts.

The 12V DC power supply should have a minimum rated output of 1 Amp

Wiring Diagrams

Basic Wiring

Security+ 2.0 Wiring

In this diagram the Reed Switch is “switching” Negative DC Voltage. While it will work in reverse (with the Reed Switch, “switching” positive), it is generally safer and the industry standard to wire as shown above.

Configuring the Shelly Plus 1 in the Smart Control App

Adding the device to Shelly Smart Control.

  1. Open the Shelly Smart Control app.

  2. Tap the blue + icon at the bottom right.

  3. Tap + Add a New Device.

image-20240410-201558.png

  1. Tap Add Via WiFi (AP Scan).

image-20240410-201629.png

  1. Tap Next.

  2. Tap the relay.

  3. Tap Next.

  4. Tap + Add Device. The inclusion process lasts for several moments.

image-20240410-201704.png

  1. Type a name for the device.

  2. Select an image to represent the device in the Smart Control app.

  3. Select the Room to add the device to. Tap Save.

  4. Tap Next. The device is associated with your Smart Control account.

image-20240410-201745.png

The relay is now included in the Smart Control app and can be controlled from any location where internet is available.

Updating the Firmware of the Device.

  1. Tap the device to update.

  2. Tap the Settings button.

  3. Tap the Firmware version dropdown.

  4. The option to enable auto-update is presented, as is the current and available firmware version. Tap Update, then tap Update again.

  5. The device updates

image-20240410-202512.png

  • The update process may take several moments and require resetting the device. It is not recommended to perform a firmware update if the device is not physically reachable.

  • Certain devices may need to be “awoken” to apply the update. In this case, once the update has been completed within the Smart Control app, press the device’s button for the firmware update to take effect.

Creating an Auto Off Timer

  1. In the Shelly Smart Control app, tap the Plus 1

  2. Tap the Timer icon.

  3. Tap the When on, turn off after XX seconds checkbox.

  4. Enter 0.5 and tap Save. The App will confirm the change

image-20240410-203604.png


Configuring the Input State Display

  1. Tap the Application settings tab.

  2. Select Add input state identifier to the power button.

image-20240410-200428.png

Configuring Input/Output Settings

  1. In the Shelly Smart Control app, tap the device to be configured.

  2. Tap the Settings tab.

  3. Tap the Input/Output Settings dropdown.

  4. Select input button/switch mode - Select whether this relay will be activated by a Button or Switch. This selection determines the availability of additional settings.

  5. Set relay type – Select Set Shelly device to be in "Detached" switch mode - switch is separated from the relays.

  6. Set relay power on default - Select Configure Shelly Device to Turn OFF, when it has power.

  7. Tap Save.

image-20240410-200457.png

Conclusion

In conclusion, the integration of a Shelly Plus 1 with a 12V DC power supply, in conjunction with a reed switch connected to its switch input, presents a robust and efficient solution for controlling garage doors. This guide has navigated through the necessary steps, from setup and wiring to configuration, ensuring that dealers, integrators, installers, and technicians are well-equipped to implement this solution effectively.
The versatility of the Shelly Plus 1, powered by a stable 12V DC source, combined with the reliability of a reed switch for door status detection, offers a significant advantage in creating smart and responsive garage door systems. The practical applications of this setup extend beyond mere convenience, offering enhanced security, seamless integration with home automation systems, and the flexibility to adapt to a wide range of scenarios and user needs.

  • No labels